Видео

I ordered one from y'all the other day can't wait to get it :)

Excellent video, even 10 years later, thank you!

This is my go to video every time, before I use my Festool router. Thanks!

And easy for “cutting off” your hearing

Must have missed angle adjustments.

Brilliantly explained

the best video on this !!!!!!

Perfectly explained. Thank you

Clear and concise communication. Best explanation I've seen.

Thank you!

I enjoy your videos but the quality of the camera needs improvement. It is very grainy and hard to watch, at least for me.

Ok. 10 year old video. But this is exactly what I needed to know. It’s what I’ve been looking for. Thank you for this.

It is a rebranded BMI Pocket Tape 405 Visio at a premium cost, truly dreadful, does not always retract, and is a nightmare to reassemble.

"has anyone had problems with the spring on the bottom holding the blade holder,,,mine wont stay attached when you release the top tension

Kreg is a huge company. WHY is the audio only one channel (left)?!?!

How do you stop 30mm copy ring/ template guide from moving and stuffing up your work

Very poor ad video. Doesn't show all the features of the Jet.

How about on concrete walls let me know thanks

The ONLY thing you could have discussed was taking "incremental" cuts, because you probably would NOT be taking a 3/4 cut in one swipe.

After watching 15 different videos, finally found one that is clear and explained from A to Z, thanks

Ive watched a ton of videos and no one has mentioned the lack of the fence guide having a table height support when extended out. The Dewalt fence had a mechanism that flipped over so your wood couldnt sink or tip into the open area when ripping sheet stock. Its def something that could make this better and more error free.

I have the OF 1400 and my collet does not center within the guide bushing at all. There is enough play in the plunge rod bushings to cause it to move all over the place. Where is the high quality Festool promotes??? But... the dust collection is spot on!

The depth adjustment is not easy, it needs a better explanation. You are better off with a drill press where you can spin the depth of ajustement wheel and measure it with a caliper this is very inaccurate for precision work

Here’s my testimonial: unreliable, not precise, sneeze near it and calibration is blown, and Festool themselves cannot calibrate these things. But dust collection is good. You’ll just spend many more hours multi-cutting your miter cuts to make them tight.

For whatever project start with a secure base. 4000 dollars later all your connection dreams will come true.

I've tried all of the above and more to get my Jet 1632 to stop tracking to the right. The factory belt that came on the machine I tore accidentally. I have gone through 4 replacement belts and not one will stay in position. I've contacted Jet Tools numerous times and haven't gotten a single response. Machine has 10 hours of use and can't use it unless I sit at the machine with an allen wrench and constantly readjust while sanding. Pissed! Anyone know where I can get a rubber belt for it?

Total BS ! Just cut on the flat, change the miter and bevel angles end of story.

Annd- by far the most expensive. And try doing it in situ.

*Only issue is that the brush attachment (which is the most used **MyBest.Tools** when cleaning auto carpet) is not included and has to be ordered separate as it doesn’t come with these.*

how's anthony

This thing is a death trap Bought it from lowes Returning it after 2 cuts Not supported correctly Pieces will fly off

Best explanation on the internet.

*This is my second WEN tool and they are both great **MyBest.Tools** I needed to do some trim work around the house and needed a scroll saw for the intricate work. No complaints so far.*

Great share thank you so much!

You are an exceptional teacher. Thank you as a newbie with new Festool tools……

I’m going to be staining and finishing my oak stairs. I’ve been told I need to do 2 coats of stain waiting 24 hours to dry each time then “as many coats of lacquer that I have the patience for…and use a “buff pad”. Do I need to use the sanding technique shown here between every coat or just at the end?

Very helpful

Forgot to tell everyone you have to cut the crown upside down. Very important step.

Does this fit the CT 36 Vac system

This guy is so clear and easy to understand. Just enough info to get the job done right without over talking.

When you cut it that way, do you always cut at a 45 angle?

do u get snipe, mine is getting it on the leading edge, is there a video on adjusting for getting rid of the snipe?

I need that for prepping millwork

terrible job of expaining it idk how yall think he explained it so well I'm so confused now

would you mind saying what the footprint of your drum sander was? I’d like the make a flip top stand for my planer and this Jet drum sander but trying to figure out how much space the drum sander will need!

Some good info here, but a lot left out. For in depth professional tutorial look at Spencer Lewis channel, inside carpentry.

Thank you. Idk why festool doesn't make a video or even show you in the instructions.

Just saw this again Greg, nice refresher, about to do a bunch of rabbets. I know it took time and energy for you to do these videos, and that is still much appreciated.

Mine works too. I used the Woodglut plans and performed it without any problems.

Baby powder works better than chaulk. Mix it with some blue and you'll be gravy and smellin as clean as a fresh daiper. Lol